Aircraft Fire Detection – Spot Fire detection Systems
For Aircraft and aviation related components, reliable high temperature detection is a key system for preventing a wide variety of in-flight system failures, or activating fail-safe mechanisms especially in so-called “spot-fire detection” applications. Indeed CPI’s X1 thermal switch is often used by both American and European avionics manufacturers and integrators as a thermal switch solution for spot detection of overtemperature conditions in systems throughout the aircraft. CPI’s design is a standalone thermal switch. It makes/breaks its connections locally and does not require a computer to reinterpret electrical signals from a flimsy temp sensor. It’s simple, reliable, and cost effective. This coupled with its overall accuracy make it the final solution for most critical avionics temperature applications.
CPI’s thermal switches have been flying around the world in commercial aircraft for decades. This may have something to do with manufacturers realizing that in addition to superior thermal performance, vibration resistance, and electro-mechanical endurance, our switches are just a whole lot less expensive than Fenwal, and other solutions commonly used. Recent integrations include FAA approval as a Fenwal replacement on Gulfstream jets, use in the De Havilland “Twin Otter” aircraft, and use by specialty aircraft manufacturer Diamond Aircraft in Europe to name a few.
Thermal Switch Uses in Modern Aircraft
Modern jets use a few different thermal sensing elements depending on what is being monitored and the temperature ranges involved, etc… Spot fire detection systems refer to systems where overheat conditions are monitored at a specific point in a compartment or LRU bay. In order to receive FAA approval, these systems must demonstrate superior detection performance and have the proven ruggedness to survive in the harsh thermal and vibrational environment of modern aircraft.
Typical zones on aircraft that employ spot fire detection include:
- Auxiliary power unit (APU)
- Engine compartments
- Cargo and baggage compartments
- Lavatories on transport aircraft
- Electronic bays
- Wheel wells
Several detectors, or sensing devices, are available to solve these detection challenges, encompassing a number of different technologies. Many modern aircraft have some type of thermal switch system or thermocouple system. A thermal switch system has one or more indicator lights or audible alarms that trip when a thermal limit is reached.
They are sometimes connected in parallel with each other but in series with the indicator lights. If the temperature rises above a set value in any one section of the circuit, the thermal switch closes, completing the light circuit to indicate a fire or overheat condition. No set number of thermal switches is required; the exact number is usually determined by the aircraft manufacturer. On some installations, all the thermal detectors are connected to one light; on others, there may be one thermal switch for each indicator light.
CPI Rod & Tube Series Thermal Switches for Avionics Applications
Recently CPI thermal switches like our X1 have seen increasing use as replacements for other thermals owing to their extreme mechanical endurance, setpoint precision, and much lower unit cost making them extremely good choices in spares and retrofit applications. In a recent retrofit application undertaken for a Gulfstream, the CPI X1 thermal switch was qualified to replace the equivalent Fenwal Switch for almost half the cost. The CPI X1 Thermal Switch has 100% equivalent functionality and accuracy with arguably superior electromechanical endurance.
CPI’s X1 Series thermal can maintain a setpoint anywhere from 0 to 850F, with a +/- 5F tolerance standard. Tighter tolerances are available. CPI thermal switches are made entirely in the USA at our manufacturing facility in East Hanover New Jersey.
|· Factory Adjustable Set Point||Temperature Range 0F -1850F
(-17C to 1,000C)
|· Highly Vibration Resistant||Response time max 5s|
|· Stainless-steel and inconel construction||Different Probe lengths from 2.25” to 5.00”|
|· Rapid Response Time and tight tolerance versions available||Available in close-on-fall, open-on-fall, close-on-rise, open-on-rise configurations|
Consider CPI Thermal Switches for your Next Spares Order
It makes good economic sense to consider CPI thermal switches for your next retrofit program, or as a design-in when your current thermals are too scarce or too expensive, or both! CPI’s USA made thermal switches are readily available through distribution, or directly from the factory for special configurations.
For more information, Contact your CPI Solutions team today.
Make The "Switch" to CPI
If your momentary switch application demands high performance, we think you should demand CPI. Please call us today to speak with our engineering team about your needs.